May 30, 2026 at 12:30 PM#1
Got my latest Janoshik results back and I realized a lot of people in this community don't actually know how to read an HPLC report. I work in analytical chemistry (pharma sector) so let me break this down.
What you'll see on a Janoshik HPLC report:
1. Chromatogram — the actual graph with peaks. X-axis is retention time (minutes), Y-axis is signal intensity (mAU)
2. Peak table — lists each detected peak, its retention time, area, and area %
3. Purity percentage — the main peak area as a % of total peak area
4. Identity confirmation — whether the main peak's retention time matches the reference standard
What "good" results look like for GLP-1 peptides:
- Purity ≥ 95% = excellent, pharmaceutical grade territory
- Purity 90-95% = acceptable for research peptides
- Purity 85-90% = borderline, I'd want to know what the impurities are
- Purity < 85% = return/discard, not worth the risk
The purity number is the single most important figure. But don't ignore the rest of the data. 📊
33 3JenMemphis, pat_auckland, Dr.GastroMayo and 30 others
Reply Quote Save Share Report
May 30, 2026 at 12:51 PM#2
This is so helpful. I just got my first result back — tirzepatide from [vendor]. Report says 97.3% purity with a main peak at retention time 12.4 min. There are two small impurity peaks at 8.2 min (1.1%) and 14.7 min (1.6%).
Is this good? Should I be worried about those impurity peaks?
Last edited: May 30, 2026 at 5:51 PM
32 2KarenAZ_mom, zoe_NC, Dr.ObesityLA and 29 others
Reply Quote Save Share Report
May 30, 2026 at 1:12 PM#3
97.3% is excellent — that's genuinely pharmaceutical grade purity. For context, the FDA approval for Mounjaro (brand tirzepatide) requires ≥95% purity.
Those small impurity peaks at 1.1% and 1.6% are completely normal and expected in peptide synthesis. They're most likely:
- Truncated sequences — shorter versions of the peptide that didn't fully synthesize
- Oxidized forms — the peptide with a slightly modified amino acid
- Deletion peptides — missing one amino acid in the chain
None of these are dangerous at those levels. They're just inactive or minimally active fragments. You'd need impurities above 5% before I'd start asking questions about what they actually are.
Your vendor did well on this batch. 👍
31 1laura_annarbor, JenMemphis, pat_auckland and 28 others
Reply Quote Save Share Report
Janoshik Analytical — Independent Testing
Trusted third-party HPLC & mass spectrometry analysis. Verify peptide purity with the lab the community relies on. Independent. Accurate. Transparent.
Verify Your PeptidesGL Biochem (Shanghai) Ltd. — Direct Manufacturer
Est. 1998. The synthesis house behind the vials you send for testing. ISO 9001 and cGMP certified, 1,500+ staff, batch-specific COA with every order.
Browse GL BiochemMay 30, 2026 at 1:33 PM#4
Good breakdown. Let me add something about retention time because this is how identity is confirmed.
Every compound has a characteristic retention time on a given HPLC column under specific conditions. Janoshik runs reference standards alongside your sample. If your sample's main peak elutes at the same time (±0.2 min typically) as the reference standard, that confirms identity.
> If the purity is 98% but the retention time doesn't match the reference standard, you have a very pure sample of the wrong compound.
This has happened. I've seen a result where someone sent in "semaglutide" and it came back 96% pure — but the retention time matched BPC-157, not semaglutide. The vendor had mislabeled the vials. Without the identity confirmation, you'd think everything was fine.
Always check the identity match, not just the purity number.
30 0TomFromTexas, mike.trainer_LA, sarah_nash92 and 27 others
Reply Quote Save Share Report
May 30, 2026 at 3:27 PM#5
Wow, that's terrifying. So a bad actor could sell literally anything and if you only looked at purity %, you'd never know?
29 24tampaLisa73, KarenAZ_mom, zoe_NC and 26 others
Reply Quote Save Share Report